中文字幕久久人妻中出一区,久久久久这里有精品,91福利丨porny丨在线

鑄件（HT250）

　　巨岡磨床主機座,、工作臺等全部鑄件體均采用HT250高等級灰口鑄鐵,，并經由有限元分析與計算，達到提高剛性與質量的工程需求,，每件鑄件均經過高溫回火和6個月以上的自然時效方式消除內應力(鑄件在爐內升溫至550一570,，保溫5~6H,再以每小時50度降至100度以下),，機床床體穩定不變形，并具有良好的抗彎及抗扭應力,，確保了巨岡磨床持久工作精度,。
　　Al our castings such as main engine seat , workbench , etcof grinders are HT250 high - grade gray cast iron , whichcan meet the engirieering demands of imp foving rigidityand quality through finite analysis and calculations . Everycasting has undergone high temperature tempering andnatural failure of over 6 months in order to eliminate internalstress ( al castings are heated to 550-570 in the fumacemaintain temperature lor 5-6H, and then drop below 100Cata rate of 50'C per hour ) so that the machine body can bestable and free of defomation, and beoome superior in temsof resistance to bending and torsion stress toensurethe longte mWorking acuracy of the grinder.

人工鏟刮

　　巨岡磨床采用硬軌全人工刮研工藝，崗位員工工作經驗均達10年以上,，鏟刮部件精度基準點控制在每平方厘米10一12點范圍內,，導軌面貼合進口高品質鐵氟龍?jiān)黾幽湍バ裕瑴p低阻尼系數,，能給機床運行提供足夠的研磨精度保證
　　Our arindina machines are al fited with fuly manual scraping process of hard track . Al workers have the workincexperence of over 10 years . The precision reference point of the scraping parts is controlled within 10-12points percm The guide ralil surface is ited with imported hioh -auality Teon to enhance abrasion resistance and reducedamping coeficient , so as to ensure enough grinding accuracy far machine running .

滾珠絲杠

　　巨岡磨床所采用的絲桿均為P3級高精度滾珠絲桿滾動摩擦系數小,，傳動效率高，其效率可達90%以上,，摩擦系數在0.002~0.005;有效降低摩擦系數與速度的差異,，起動扭矩接近運轉扭矩，所以工作平穩無沖擊,，磨損小且壽命長,，可用調整裝置調整頂緊力，傳動精度與剛度均得到提高具有傳動可逆性,，即可將回轉運動變?yōu)橹本€運動又可把直線運動變?yōu)榛剞D(zhuǎn)運動,，有效提高機床工作精度和淑嚨址墑淆揉按定性,。
　　The screws of our grinders are as of 的 high precisiontype , which is featured by low rolling friction ooefficientand high transmission efficiency ( above 9096).Thefriction coefficient fro .002-0.005:it can reduce theciference between friction ooefficient and speed effectivelyand the starting torque is similar to running torquewhich oontributes to stable and impact - free working ，litle abrasion and long service life , Moreover, the gapcan be adjusted by adjustment device in order to imp Tove transmission accuracy and rigidity . In additiontransmission reversibility is designed to change therotary motion into linear moticn or vice versa , so asto improve the workingaccuracy and stability of themachine dramaticaly .

主軸性能表述

　　巨岡磨床全系列所使用的每一支主軸,，都完全由臺灣知名品牌 POSA,、HS 提供，主軸配裝日本NSK-CP4級精密斜角滾珠軸承,，保證主軸偏轉遠低于0.002mm,，其主軸工作穩定性和耐用性可滿足機床正常使用十年以上
　　Each spindle used in the whole series of Jugang grindingmachines is completely oomposed of Taiwan famousbrands POSA and HS provide, and the spindle is equippedwith Japan NSK-CP4 precision bevel bal bearing ensuresspindle deflection It is far less than 0.002mm, and itsworking stability and durability can be Meet the normaluse of the machine tool for more than 10 years